moin bin linux-noob, daher einige fragen...
es geht dabei quasi um das, was so auf deinem bildschirm angezeigt wird, wenn du den rechner startest
wie kann ich denn vor dem login die relevanten daten als text speichern? ich kann zwar esc drücken damit ne auflistung angezeigt wird in der steht was geladen wurde und was nicht. aber die kann man nur so lange sehen wie die login-aufforderung noch nicht angezeigt wird
1 kein apm-modul, aber ein apm-daemon. oder moeglicherweise der versuch, die 1 platten in sleep zu versetzen? 2 Okay, das apm-modul ist nicht geladen, aber der apmd läuft
apm war ausgeschaltet und apmd hab ich mal ausgeschaltet, aber linux hängt trotzdem nach 15 minuten (auf dem monitor sieht man nicht den als letztes angezeigten bildschirm sondern einen blauen hintergrund der verzerrt aussieht, falls jemand was damit anfangen kann)
Welches Gerät ist bei Dir Master am 2. IDE-Kanal? Könnte sein, daß Du nicht mehr viel Freude daran hast...
ich denke ma ne 2. festplatte
Ist das wirklich direkt nach dem Booten? Wenn ja, schalt' bitter erst Deine Firewall ab.
diesmal ohne firewall: Linux version 2.4.22-10mdk (nplanel@no.mandrakesoft.com) (gcc version 3.3.1 (Mandrake Linux 9.2 3.3.1-2mdk)) #1 Thu Sep 18 12:30:58 CEST 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fef0000 (usable) BIOS-e820: 000000001fef0000 - 000000001feff000 (ACPI data) BIOS-e820: 000000001feff000 - 000000001ff00000 (ACPI NVS) BIOS-e820: 000000001ff00000 - 0000000020000000 (usable) BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 512MB LOWMEM available. ACPI: have wakeup address 0xc0001000 On node 0 totalpages: 131072 zone(0): 4096 pages. zone(1): 126976 pages. zone(2): 0 pages. ACPI: RSDP (v000 PTLTD ) @ 0x000f7c10 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1fefbe4d ACPI: FADT (v001 FSC D132X 0x06040000 0x000f4240) @ 0x1fefbe7d ACPI: MADT (v001 FSC APIC 0x06040000 CSF 0x00000000) @ 0x1fefef7e ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x1fefefd8 ACPI: DSDT (v001 FSC D132X 0x06040000 MSFT 0x0100000c) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 Pentium 4(tm) APIC version 20 ACPI: LAPIC_NMI (acpi_id[0xff] polarity[0x1] trigger[0x1] lint[0x1]) Building zonelist for node : 0 Kernel command line: auto BOOT_IMAGE=linux ro root=301 devfs=mount hdd=ide-scsi acpi=ht splash=silent ide_setup: hdd=ide-scsi bootsplash: silent mode. Found and enabled local APIC! Initializing CPU#0 Detected 1699.075 MHz processor. Console: colour dummy device 80x25 Calibrating delay loop... 3381.65 BogoMIPS Memory: 514640k/524288k available (1508k kernel code, 9196k reserved, -1961k data, 156k init, 0k highmem, 0k BadRAM) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 256K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 3febfbff 00000000 00000000 00000000 CPU: Common caps: 3febfbff 00000000 00000000 00000000 CPU: Intel(R) Pentium(R) 4 CPU 1700MHz stepping 0a Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 1699.0555 MHz. ..... host bus clock speed is 99.9443 MHz. cpu: 0, clocks: 999443, slice: 499721 CPU0<T0:999440,T1:499712,D:7,S:499721,C:999443> mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel ACPI: Subsystem revision 20030813 ACPI: Interpreter disabled. PCI: PCI BIOS revision 2.10 entry at 0xfd963, last bus=2 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: ACPI tables contain no PCI IRQ routing entries PCI: Probing PCI hardware (bus 00) Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge PCI: Using IRQ router PIIX [8086/2440] at 00:1f.0 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) Starting kswapd kinoded started VFS: Disk quotas vdquot_6.5.1 devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 vesafb: framebuffer at 0xf0000000, mapped to 0xe0800000, size 1875k vesafb: mode is 800x600x16, linelength=1600, pages=2 vesafb: protected mode interface info at c000:ec60 vesafb: scrolling: redraw vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 Looking for splash picture.... silenjpeg size 107888 bytes, found (800x600, 107840 bytes, v3). Got silent jpeg. Got silent jpeg. Console: switching to colour frame buffer device 92x32 fb0: VESA VGA frame buffer device pty: 1024 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH2: IDE controller at PCI slot 00:1f.1 ICH2: chipset revision 18 ICH2: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x2400-0x2407, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x2408-0x240f, BIOS settings: hdc:pio, hdd:pio hda: ST360020A, ATA DISK drive hdb: Maxtor 6Y060L0, ATA DISK drive blk: queue c0180d20, I/O limit 4095Mb (mask 0xffffffff) blk: queue c0180e5c, I/O limit 4095Mb (mask 0xffffffff) hdc: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive hdd: AOPEN CD-RW CRW2440, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=7297/255/63, UDMA(100) hdb: attached ide-disk driver. hdb: host protected area => 1 hdb: 120103200 sectors (61493 MB) w/2048KiB Cache, CHS=7476/255/63, UDMA(100) Partition check: /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 > /dev/ide/host0/bus0/target1/lun0: p1 < p5 > ide: late registration of driver. md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 131072 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Swsusp 1.0.3: Missing or invalid swap partition location (resume= parameter). Disabled. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 300k freed VFS: Mounted root (ext2 filesystem). Mounted devfs on /dev Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Mounted devfs on /dev Freeing unused kernel memory: 156k freed Got silent jpeg. Real Time Clock Driver v1.10e usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.275 $ time 12:42:04 Sep 18 2003 usb-uhci.c: High bandwidth mode enabled PCI: Assigned IRQ 9 for device 00:1f.2 PCI: Sharing IRQ 9 with 02:09.0 PCI: Setting latency timer of device 00:1f.2 to 64 usb-uhci.c: USB UHCI at I/O 0x1400, IRQ 9 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 11 for device 00:1f.4 PCI: Setting latency timer of device 00:1f.4 to 64 usb-uhci.c: USB UHCI at I/O 0x1c00, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver usbdevfs: remount parameter error EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal SCSI subsystem driver Revision: 1.00 hdd: attached ide-scsi driver. scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: AOPEN Model: CD-RW CRW2440 Rev: 1.00 Type: CD-ROM ANSI SCSI revision: 02 hdc: attached ide-cdrom driver. hdc: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal EXT3-fs: mounted filesystem with ordered data mode. NTFS driver 2.1.4a [Flags: R/O MODULE]. NTFS volume version 3.1. 8139too Fast Ethernet driver 0.9.26 PCI: Found IRQ 9 for device 02:09.0 PCI: Sharing IRQ 9 with 00:1f.2 eth0: RealTek RTL8139 Fast Ethernet at 0xe0bd9000, 00:40:f4:3c:83:c7, IRQ 9 eth0: Identified 8139 chip type 'RTL-8139C' inserting floppy driver for 2.4.22-10mdk Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray sr0: mmc-3 profile capable, current profile: 0h sr0: mmc-3 profile: 0h sr0: mmc-3 profile: 0h sr0: mmc-3 profile: 0h sr0: mmc-3 profile: 0h IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: Each connection entry needs 116 bytes at least IPVS: ipvs loaded. eth0: Setting 10mbps full-duplex based on auto-negotiated partner ability 4061. CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Intel 810 + AC97 Audio, version 0.24, 12:41:23 Sep 18 2003 PCI: Found IRQ 5 for device 00:1f.5 PCI: Sharing IRQ 5 with 00:1f.3 PCI: Setting latency timer of device 00:1f.5 to 64 i810: Intel ICH2 found at IO 0x2000 and 0x1000, MEM 0x0000 and 0x0000, IRQ 5 i810_audio: Audio Controller supports 6 channels. i810_audio: Defaulting to base 2 channel mode. i810_audio: Resetting connection 0 ac97_codec: AC97 Audio codec, id: ADS96 (Analog Devices AD1885) i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not present), total channels = 2 parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP] lp0: using parport0 (polling). Looking for splash picture.... found (800x600, 14470 bytes, v3). Splash status on console 0 changed to on Looking for splash picture.... found (800x600, 14470 bytes, v3). Splash status on console 1 changed to on Looking for splash picture.... found (800x600, 14470 bytes, v3). Splash status on console 2 changed to on Looking for splash picture.... found (800x600, 14470 bytes, v3). Splash status on console 3 changed to on Looking for splash picture.... found (800x600, 14470 bytes, v3). Splash status on console 4 changed to on Looking for splash picture.... found (800x600, 14470 bytes, v3). Splash status on console 5 changed to on