probleme mit i2o

[Toens Bueker]

Thomas Balsfulland <tbals at ctrl-c.de> meinte:

> bei mir sieht ja eigentlich gleich aus. nur die adressen sind anders.

> und das ist ja eigentlich genau das was ich will:
> das raid nutzen und die einzelnen platten monitoren koennen.

Was meinst Du denn mit "monitoren"?

> > Wie gesagt - ich habe die gleiche Büxe hier unter Xen laufen und der Kernel
> > hat i2o überhaupt nicht an.
> 
> funktionieret raidutils denn bei dir?

Ja:

bla:# raidutil -L all
RAIDUTIL  Version: 3.31  Date: 8/12/2002  LINUX CLI Configuration Utility
Adaptec ENGINE  Version: 3.31  Date: 8/12/2002  Adaptec LINUX SCSI Engine

#  b0 b1 b2  Controller     Cache  FW    NVRAM     Serial     Status
---------------------------------------------------------------------------
d0 --        ADAP2100S      16MB   FS02  SI  V2.1  BB0A24320PTOptimal

Physical View
Address    Type              Manufacturer/Model    Capacity  Status
---------------------------------------------------------------------------
d0b0t0d0   Disk Drive (DASD) FUJITSU  MAP3367NC    35046MB   Optimal
d0b0t1d0   Disk Drive (DASD) FUJITSU  MAP3367NC    35046MB   Optimal
d0b0t8d0   SAF-TE            SDR      GEM318       -----     Optimal

Logical View
Address       Type              Manufacturer/Model Capacity  Status
---------------------------------------------------------------------------
d0b0t0d0      RAID 1 (Mirrored) ADAPTEC  RAID-1    34700MB   Optimal 
 d0b0t0d0     Disk Drive (DASD) FUJITSU  MAP3367NC 35046MB   Optimal
 d0b0t1d0     Disk Drive (DASD) FUJITSU  MAP3367NC 35046MB   Optimal


Address    Max Speed  Actual Rate / Width
---------------------------------------------------------------------------
d0b0t0d0   Ultra3     160 MB/sec    wide
d0b0t1d0   Ultra3     160 MB/sec    wide
d0b0t8d0   Ultra3     ?

Address    Manufacturer/Model        Write Cache Mode
---------------------------------------------------------------------------
d0b0t0d0   ADAPTEC  RAID-1           Write Through
 d0b0t0d0  FUJITSU  MAP3367NC        Write Through
 d0b0t1d0  FUJITSU  MAP3367NC        Write Through
  
#  Controller     Cache  FW    NVRAM     BIOS   SMOR      Serial
---------------------------------------------------------------------------
d0 ADAP2100S      16MB   FS02  SI  V2.1  1.48   1.12/66I  BB0A24320PT

#  Controller      Status     Voltage  Current  Full Cap  Rem Cap  Rem Time
---------------------------------------------------------------------------
d0 ADAP2100S       No battery

Address    Manufacturer/Model        FW          Serial        123456789012
---------------------------------------------------------------------------
d0b0t0d0   FUJITSU  MAP3367NC        5205     UPP7P3300G3Y     -XXXX---XOX-
d0b0t1d0   FUJITSU  MAP3367NC        5205     UPP7P3300FJ5     -XXXX---XOX-
d0b0t8d0   SDR      GEM318           0        1                -------X-O-X

Capabilities Map:  Column 1 = Soft Reset
                   Column 2 = Cmd Queuing
                   Column 3 = Linked Cmds
                   Column 4 = Synchronous
                   Column 5 = Wide 16
                   Column 6 = Wide 32
                   Column 7 = Relative Addr
                   Column 8 = SCSI II
                   Column 9 = S.M.A.R.T.
                   Column 0 = SCAM
                   Column 1 = SCSI-3
                   Column 2 = SAF-TE
   X = Capability Exists, - = Capability does not exist, O = Not Supported


Tschö
Töns
-- 
There is no safe distance.